Contactar Proveedor
Mr. Nicolas
Deja un mensaje Mr. Nicolas¿Qué puedo hacer por ti?
Shenzhen Keith Electronic Equipment Co., Ltd.
| Tipo de Pago: | T/T |
|---|---|
| Incoterm: | FOB,CFR,EXW |
| Cantidad de pedido mínima: | 1 Bag/Bags |
| Plazo de entrega: | 7 días |
Información básica
Modelo: NM-EJR5A, NM-EJR6A
Información adicional
Paquete: Envasado al vacío en cajas de madera.
Marca: Panasonic
transporte: Ocean
Lugar de origen: Japón
Hafen: Hong Kong
DDescripción
Caracteristicas
La RL132 es una máquina de inserción de componentes radiales con sistema de pasador de guía capaz de inserción de alta velocidad en un tiempo de contacto de 0.14 s / componente,
lo que también permite ahorrar energía y reducir el ruido de operación.
1.Inserción de alta velocidad y alta densidad
La inserción de alta velocidad con un tiempo de contacto máximo de 0,14 s / componente permite una inserción de mayor densidad.
2. Tasa de operación mejorada
• El alimentador de componentes fijo proporciona componentes sin detener la máquina, lo que permite una operación de más horas.
• La función de recuperación de suministro automático y las características de programación también contribuyen a que la máquina funcione durante más horas.
3.Fiabilidad más alta
Las posiciones de inserción se corrigen según el desplazamiento obtenido mediante el reconocimiento visual de los orificios de inserción en la placa de PC, lo que garantiza una inserción altamente confiable.
Especificaciones de la máquina
| Model ID | RL132 | ||
| Model No. | NM-EJR5A | NM-EJR6A | |
| PCB dimensions (mm) | L 50 x W 50 to L 508 x W 381 | ||
| Max.speed | 0.14 s/component | ||
| No.of component inputs | 40 | 80 (Connection mode), 40 + 40 (Exchange mode) | |
| Applicable components |
Pitch 2.5/5.0 mm (standard), 7.5 mm and 10 mm (option), Resistor, Electrolytic capacitor, Ceramic capacitor, LED, Transistor, Filter, Resistor network |
||
| PCB exchange time | about 2 s to about 4 s (Room temperature 20 °C) | ||
| Insertion direction | 360°direction by 1°increment | ||
|
Electric source *1 |
3-phase AC 200 V, 3.5 kVA | ||
| Pneumatic source | 0.5 MPa, 80 L/min (A.N.R.) | ||
| Dimensions (mm) | W 2 104 x D 2 183 x H 1 575 *2 | W 3 200 x D 2 417 x H 1 575 *2 | |
|
Mass *3 |
1750 kg | 2350 kg | |
| Item | Details | |
| Power supply |
• Rated voltage 3-phase 200 / 220 V ± 10 V selectable 380 / 400 / 420 / 480 V ±20 V selectable • Frequency 50 / 60 Hz • Rated capacity Approx. 3.5kVA |
|
| Air supply |
• Supplied air pressure Min. 0.45 MPa to Max. 0.8 MPa (Operation air pressure: 0.45 ~ 0.5 MPa) • Supplied air mass Approx. 80 L / min. (A.N.R) Note: Quick coupler attached (SMC KK13P-03M, KK13S-03F). |
|
| Dimensions |
• NM-EJR5A W2,104 x D2,183 x H1,575 mm (Not including signal tower) • NM-EJR6A W3,200 x D2,417 x H1,575 mm (Not including signal tower) |
|
| Mass |
• NM-EJR5A Approx. 1,750 kg (main body only) • NM-EJR6A Approx. 2,350 kg (main body only) |
|
| Environmental requirements | • Ambient temperature 20°C ± 10°C | |
| Operating controls |
• Interactive operation via color LCD touch screen English/Japanese/Chinese selectable with a single button Recognition screen (displays the recognized board image on a superimposed window) Hierarchical menu (Operator/Engineer) • I /O functions SD card slot (standard equipment) • Communication LAN comunicaton (TCP/IP) |
|
| Coating color | • Standard color White: W-13 (G50) | |
Rendimiento básico
| Item | Details |
| Insertion tact time |
• Max. tact time: Approx. 0.14 s/point (0.17, 0.20, 0.25, 0.3 s/point changeable) =REMARKS= *1 X-Y table movement at the tact time of 0.14 s/point: Within 36 mm Insertion direction: each 1degree (0°- 90°, 0°- (-)90° : 0.14 s/point) (90°- 180°,91°- (-)180°: 0.20 s/point)*2 The tact time above is enabled only when components are continuousl taped. (Tact time varies if there are missing portions.) *3 Tact time varies between the beginning and the last of the insertion.*4 Tact time varies when new components are inserted for recovery. *5 Tact time varies also if 10 or more feeders are operated at a time due to the NC data setting. *6 Tact time must be set between 0.25 and 0.30 s when inserting components more than 12 mm in diameter or more than 18 mm in height |
| Applicable components |
Insertion pitch: 2.5 and 5.0 mm (standard), 7.5 and 10.0 mm (option) Height: Hn = Max. 23 mm Diameter: D = Max. 13 mmResistors, electrolytic capacitors, ceramic capacitors, LEDs, transistors, filters and resistor networks |
| Component packaging |
• Taping (in pack or reel) =REMARKS= Component pack must be lower than 360 mm and width less than 62 mm. Component reel must be up to 360 mm in diameter and 62 mm in width. Bracket and reel shaft are required. Cannot be used on the upper stage of the supply unit. |
| PCB replacement time |
• Approx. 2 second (Ambient temperature: 20°C): =REMARKS= PCB replacement time only includes time for loading. It takes approx. 4 to 5 seconds including the table return time. |
| Applicable PCB |
• Dimensions Min. 50 x 50 mm to Max. 508 x 381 mm Width-to-length ratio: Width should be equal to or less than length. Consult us for boards having width longer than length. • Allowable insertion areaMin. 50 x 40 mm ~ Max. 508 x 371 mm • Thickness 1.6 mm ± 0.15 mm (for standard specification) =REMARKS= Boards of thickness from 0.6 mm (min.) to 2.0 mm (max.) are applicable. Even if the board thickness is within the above range, clinched angle of the inserted lead or lead length may vary, or board transfer error may occur depending on the shapes of board or insertion holes. Please contact us in advance.
Max. 1 kg per board including inserted components. • Flow direction Right to left (Standard) or Left to right (Option) • Board positioning method Pin positioning (Standard, without positioning in the Y direction), =REMARKS= Contact us separately for edge positioning. |
| Insertion pitch |
• 2-pitch (standard), 3-pitch or 4-pitch (option) 2.5 mm and 5.0 mm (standard), 2.5 mm ,5.0 mm ,7.5 mm ,or 2.5 mm ,5.0 mm ,7.5 mm,10.0 mm (Option) |
| Insertion direction | • 360 degrees by 1 degree |
| Anvil | • Cutting & Clinch type system (Piezoelectric detection system) |
| No. of component inputs |
• NM-EJR5A 40 types • NM-EJR6A 80 types |
Especificaciones de control
| Item | Details |
| Control system | • Microcomputer system |
| Programming method |
• X-Y axes: Absolute coordinate commands • Insertion pitch: Absolute commands • Component feeder: Feeder number designation |
| Least command increment of X-Y table | • 0.01 mm / pulse |
| Program |
• Number of NC programs • Built-in flash memory 200 programs, 5000 steps / program (Note: In case of programs involving pattern repeat, the total number of steps after expanding the program must be less than 5,000.) • SD card Depends on the card capacity. (up to 2 GB) |
| Indication light | • Signal tower (3 lamps, top to bottom: red/yellow/green) |
| Hole position offset |
• Determines optimum insertion positions based on the recognition of all insertion positions to make positional corrections (XY and q). |
| Self-diagnosis function |
• Presents on the color LCD the machine status when the power is ON and situation of any troubles occurred, as well as countermeasures against the troubles. |
| Others |
• Programming functions Pana PRO J PanaPROJ the software for optimizing the balance of line consisting of multiple machines and for assigning data is available. • Data compatibility Data from conventional RH series (RH, RH6, RHP, RHP2, RH2, RH3, RH5, RHSG, RHS, RHS2, RHS2B, RHU, RHU2, RHUP, RG131 and RL131) can be directly used on the RL132. |
Shenzhen Keith Electronic Equipment Co., Ltd. "ubicada en el distrito de Baoan, Shenzhen. Es un proveedor de equipos de IA y SMT, repuestos, consumibles y materiales de consumo auxiliar en China. A lo largo de los años, hemos proporcionado equipos y piezas avanzadas para nuestros clientes para garantizar un servicio de alta calidad. Y para el mercado de exportación, estamos planeando desarrollar Europa, América del Norte, América del Sur, Sudeste de Asia, India y donde necesiten piezas de repuesto para equipos SMT.
Filosofía empresarial: cooperación, beneficio mutuo, innovación, asistencia mutua
Nos hemos adherido al concepto de gestión de marca de "centrarse en la calidad del producto y las necesidades del cliente", a través de la implementación de innovación abierta, excelente gestión de operaciones, desarrollo de recursos humanos y otras estrategias, para construir integralmente la competitividad central de la empresa, crear clientes y valores sociales, y ganar el elogio unánime de la gran cantidad de clientes y la sociedad.
Productos principales:
Panasonic Insertion Machine, Panasonic Insertion Machine Parts, Panasonic Placement Machine, Panasonic Placement Machine Parts, Panasonic Feeder & Feeder Parts, Feeder Trolley, SMT Cutter, etc. Para obtener más información sobre nuestros productos, contáctenos a través de la siguiente dirección de correo electrónico. ¡tu cooperación!
PRODUCTOS POR GRUPO : Máquina de inserción Panasonic
Productos hot
